Page tree

Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall main

Install Mounting Hardware

Cci readerinstall kit
KitID584
KitDescCoin and Card
  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Cci readerinstall kit
KitID906
KitDescCard Only - Card Models
  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Cci readerinstall kit
KitID857
KitDescCard Only - Coin Models
  1. Remove existing coin box and coin drop.

  2. Install the C-5365 Bypass Harness by removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness.
  3. Attach the C-5414 F2 Mounting Bracket to the C-6765-W-R1 Metercase Bracket using (2) C-5420 10-32 x 1/4 Pan Screws.
  4. Run any card reader harnesses through the coin slot openings and the circular hole in the C-6765-W-R1 Metercase Bracket.
  5. Install the C-6765-W-R1 Metercase Bracket so that the two threaded posts insert into the coin drop slots. Then secure it to the machine using the (2) C-1059 Kep Nuts and (2) C-1070-W Washers.

Connect Power

Cci readerinstall kit
KitID595
KitDescDryer Control - Tap incoming 120/240VAC Power
  1. Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.
  2. Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.
  3. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.
Cci readerinstall kit
KitID808
KitDescWasher Control - ACA 12VDC Accessory Power
  1. Connect the C-6204-40 12VDC Power Harness to the H10 connection on the Machine Control Assembly.
    1. Connect the green wire to a chassis ground.
  2. The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.

Connect Coin Sense Harness

Cci readerinstall kit
KitID700
KitDescFactory - Single Optical Coin Sensor
  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6250 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

Cci readerinstall kit
KitID645
KitDescPulse - Coin Connection
  1. Connect the C-5300-NC Machine Start Harness to the Coin 1 connection on the Machine Control Assembly.
Cci readerinstall kit
KitID0603
KitDescSerial - Dryer Control
  1. Connect the C-0110-TOP Machine Start Harness to the H3 connection on the Machine Control Assembly.
  2. Connect the C-0110-CP Jumper Plug to the H6 connection on the Machine Control Assembly.
Cci readerinstall kit
0
KitID582
KitDescSerial - Washer Control
  1. Connect the C-5240 Machine Start Harness to the H3 connection on the Machine Control Assembly.

Connect and Mount Reader

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameF2 Reader
PageWithExcerptCCIDOC:_Reader Ports

  1. Feed remaining harness ends through the mounting hole.
  2. Connect the free end of theC-5300-NC Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of the C-5240 or C-0110-TOP Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.
  4. (Coin and Card Installations Only) Connect the free end of the C-6250 Coin Sense Harness  to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  5. Connect the free end of the C-5500 or C-6204-40 Power Extension Harness to port 1 (Power Harness Connection Port) as shown in the image above.

Machine Configuration

Washer Control

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameACA Configuration
PageWithExcerptCCIDOC:_Machine Configuration

Dryer Control