Page tree

Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall main

Install Mounting Hardware

Cci readerinstall kit
KitID584
KitDescCoin and Card
  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Cci readerinstall kit
KitID857
KitDescCard Only - 10° Panel Coin Models
  1. Remove existing coin box and coin drop.

  2. Install the C-5365 Bypass Harness by removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness.
  3. Attach the C-5414 F2 Mounting Bracket to the C-6765-W-R1 Metercase Bracket using C-5702 Chase Nipple and C-5703 Lock Nut.
  4. Run any card reader harnesses through the coin slot openings and the circular hole in the C-6765-W-R1 Metercase Bracket.
  5. Install the C-6765-W-R1 Metercase Bracket so that the two threaded posts insert into the coin drop slots. Then secure it to the machine using the C-1059 Kep Nuts and C-1070-W Washers.

Cci readerinstall kit
KitID911
KitDescCard Only - Flat Front Panel Coin Models
  1. Remove existing coin box and coin drop.

  2. Install the C-5365 Bypass Harness by removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness.
  3. Bend the tabs outward and insert the C-0940 Vault Cover in to the coin vault opening.
  4. Apply the C-5035 Label over the opening for the coin drop.
  5. Place the C-6700-TEMP Drill Template on the desired mounting location.

  6. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  7. Refer to FasCard Mounting Guide for further instructions.

Cci readerinstall kit
KitID906
KitDescCard Only - Card Models
  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Connect Power

Cci readerinstall kit
KitID581
KitDescACA Controls
  1. Connect the C-6204-40 12VDC Power Harness to the H10 connection on the Machine Control Assembly.
    1. Connect the green wire to a chassis ground.
  2. The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.
Cci readerinstall kit
KitID837
KitDescTitanium Controls
  1. Connect the 2-pin connector from the C-6207 F2, ACA Power Harness to the 24v transformer behind the front control panel.
  2. The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.

Connect Coin Sense Harness

Cci readerinstall kit
KitID700
KitDescFactory Optical Coin Drop
  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6250 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

Cci readerinstall kit
KitID648
KitDescPulse - Coin
  1. Connect the C-5300-NC Machine Start Harness to the coin 1 connector on the Machine Control Assembly.
Cci readerinstall kit
KitID582
KitDescSerial Communication / Serial Pulse
  1. Connect the C-5240 Machine Start Harness to the the H3 connection on the Machine Control Assembly or Communication board.

Connect and Mount Reader

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameF2 Reader
PageWithExcerptCCIDOC:_Reader Ports

  1. Feed remaining harness ends through the mounting hole.
  2. If using the C-5300-NC Machine Start Harness, connect the free end to port 2 (Pulse Connection Port) as shown in the image above.
  3. If using the C-5240 Machine Start Harness, connect the free end to port 5 (Serial Connection Port) as shown in the image above.
  4. For Coin and Card setups, connect the free end of the C-6250 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  5. Connect the free end of the C-6204-40, C-6207 Power Harness to port 1 (Power Harness Connection Port) as shown in the image above.

Machine Configuration

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameACA Configuration
PageWithExcerptCCIDOC:_Machine Configuration

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameTitanium Configuration (FLW/Small Dryer)
PageWithExcerptCCIDOC:_Machine Configuration