Page tree

Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall main

Install Mounting Hardware

Cci readerinstall kit
KitID584
KitDescCoin and Card
  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Cci readerinstall kit
KitID865
KitDescCard Only - Card Ready
  1. Install the C-6970 Alliance Mounting Bracket into the opening on the control panel for mounting card readers and coin drops.
  2. Attach the C-5414 F2 Mounting Bracket to the C-6970 Alliance Mounting Bracket and secure using the C-1060 Screws.
  3. Refer to F2 FasCard Reader Mounting Guide for further instructions.
Cci readerinstall kit
KitID856
KitDescCard Only - Coin Ready
  1. Remove existing coin box and coin drop.

  2. Install the C-5365 Bypass Harness by removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness.
  3. Bend the side tabs of the C-6936 Vault Bracket outward and install into the coin vault. The tabs should snap into place securing the bracket.

  4. Place the C-5710 Rubber Grommet into the circular opening of the C-6936 Vault Bracket.
  5. Align the C-5414 F2 Mounting Bracket over the coin vault opening and then attach the to the C-6936 Vault Bracket using the (2) C-0144 screws.

  6. Apply C-5033 Label over coin drop opening.

Connect Power

Cci readerinstall kit
KitID581
  1. Connect the C-6204-40 Power Adapter Harness (12VDC power) to the H10 connection on the Machine Control Assembly.
  2. Secure the green wire beneath the ground screw.

Connect Coin Sense Harness

Cci readerinstall kit
KitID700
KitDescCoin Drop: Factory
  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6250 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

Cci readerinstall kit
KitID582
KitDescPulse or Serial
  1. Connect the C-5240 Machine Start Harness to the H3 connector on the Machine Control Assembly.

Optional: Stack Add-On Installation

Cci readerinstall kit
KitID927
KitDescPulse and Serial - Coin and Card
  1. Run C-5240-144 Machine Start Harness and C-6250-144 Coin Sense Harness to the second Machine Control Assembly.
  2. Connect C-5240-144 Machine Start Harness to the H3 connection and the C-6250-144 Coin Sense Harness to the Coin 1 connection on the second Machine Control Assembly.
  3. Connect the C-6401 Stack Add-on Board to port 5 (Serial Connection Port) on the F2 reader.
    1. Connect the Machine Start Harness connected to the upper pocket Machine Control Assembly to Unit 1 on the Stack Add-on Board.
    2. Connect the Machine Start Harness connected to the lower pocket Machine Control Assembly to Unit 2 on the Stack Add-on Board.
  4. Connect the Coin Sense Harness connected to the upper pocket Coin Drop to port 3 (Coin 1 Sense Harness Connection Port) on the F2 reader.
  5. Connect the Coin Sense Harness connected to the lower pocket Coin Drop to port 4 (Coin 2 Sense Harness Connection Port) on the F2 reader.
Cci readerinstall kit
KitID957
KitDescPulse and Serial - Card Only (Coin Ready Models)
  1. Install C-0940 Vault Cover into the coin vault for the secondary control.
  2. Run C-5240-144 Machine Start Harness to the second Machine Control Assembly.
  3. Connect C-5240-144 Machine Start Harness to the H3 connection on the second Machine Control Assembly.
  4. Connect the C-6401 Stack Add-on Board to port 5 (Serial Connection Port) on the F2 reader.
    1. Connect the Machine Start Harness connected to the upper pocket Machine Control Assembly to Unit 1 on the Stack Add-on Board.
    2. Connect the Machine Start Harness connected to the lower pocket Machine Control Assembly to Unit 2 on the Stack Add-on Board.
Cci readerinstall kit
KitID960
KitDescPulse and Serial - Card Only (Card Ready Models)
  1. Run C-5240-144 Machine Start Harness to the second Machine Control Assembly.
  2. Connect C-5240-144 Machine Start Harness to the H3 connection on the second Machine Control Assembly.
  3. Connect the C-6401 Stack Add-on Board to port 5 (Serial Connection Port) on the F2 reader.
    1. Connect the Machine Start Harness connected to the upper pocket Machine Control Assembly to Unit 1 on the Stack Add-on Board.
    2. Connect the Machine Start Harness connected to the lower pocket Machine Control Assembly to Unit 2 on the Stack Add-on Board.

Connect and Mount Reader

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameF2 Reader
PageWithExcerptCCIDOC:_Reader Ports

  1. Feed remaining harness ends through the mounting holes.
  2. Connect the free end of the C-5240 Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.
  3. Connect the free end of the C-6250 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-6204-40 Power Extension Harness to port 1 (Power Harness Connection Port) as shown in the image above.
  5. Secure the FasCard reader to base as described in the F2 Reader Mounting Guide.

Machine Configuration

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameACA Configuration
PageWithExcerptCCIDOC:_Machine Configuration