Page tree

Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall main

Install Mounting Hardware

Cci readerinstall kit
KitID584
KitDescCoin and Card
  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Cci readerinstall kit
KitID940
KitDescCard Only - Coin Model
  1. Remove existing coin box and coin drop.

  2. Install the C-0913 Drop Cover in the coin drop opening and secure using the C-1062 Keps Nuts.
  3. Run all reader harnesses through coin vault and then the hole of the C-6936 Vault Bracket.
  4. Bend the side tabs of the C-6936 Vault Bracket outward and install into the coin vault. The tabs should snap into place securing the bracket.

  5. Run all reader harnesses through the central hole of the C-5414 Reader Bracket
  6. Attach the C-5414 Reader Bracket to the C-6936 Vault Bracket using the C-0144 screw so that it is flush with the front panel.

Cci readerinstall kit
KitID995
KitDescCard Only - Card Model
  1. Remove factory card reader interface bracket.

  2. Attach C-5414 Reader Bracket to the C-6918 Mounting Bracket using  using (2) C-5702 Chase Nipple and C-5703 Lock Nut5420 10-32 x 1/4" Pan Screw.
  3. Install the C-6918 Mounting Bracket in the payment device opening and secure using the (2) C-1062 Keps Nuts.
  4. Run all reader harnesses through the center hole in the C-6918 Mounting Bracket.

Connect Power

Cci readerinstall kit
KitID595
KitDescTap Machine Power
  1. Use the C-5101 Spade Taps on the incoming power.
    1. Tap the L1 wire.
    2. Tap the N / L2 wire.
    3. Tap the Ground wire.
  2. Take the C-5210 Power Adapter Harness and connect the red tab connectors to the following wires:
    1. Connect the blue wire to the L1 wire.
    2. Connect the brown wire to the N / L2 wire.
    3. Connect the green/yellow wire to the Ground wire.
  3. Connect the 3-pin connector from the C-5210 Power Adapter Harness to the matching connection on the C-5602R1 Power Converter.
  4. Connect the 4-pin connector from the C-5602R1 Power Converter to the matching connection on the C-5500 Power Extension Harness.

Connect Coin Sense Harness

Cci readerinstall kit
KitID721
KitDescFactory Coin Drop
  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6362 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

Cci readerinstall kit
KitID997
KitDescPulse - AA3/Debit Connection
  1. Connect the C-5370 Machine Start Harness to the 8-pin J6 harness connection accessible near the coin drop.

Connect and Mount Reader

  1. Feed remaining harness ends through the mounting hole.
  2. Connect the free end of the C-5364 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of the C-6362 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5500 Power Harness to port 1.
  5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

Machine Configuration

  1. Enter Service Mode and navigate to option.
  2. Set option to J.d.
  3. Exit Service Mode.