Skip to end of metadata
Go to start of metadata

Overview

Equipment Details


Average Installation Time


On This Page

Make: Wittern


TODO


Associated Models


3578

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

Part IDDescriptionImage
C-0103-B
LaundryCard Reader V3 - RevB

Recommended Tools and Supplies (Not Included)

Installation

    Page not found for multiexcerpt macro.
The page: null was not found. Please check/update the page name used in the 'multiexcerpt-include' macro.

Install Mounting Hardware

Payment Device Bay

P/N: C-0014S
Label
TD LC Window
Qty: 1
P/N: C-0015S
Label
TD30 Insert Card Graphic
Qty: 1
P/N: C-0974
Flat Mount Bezel
Fits 3-1/2" x 4-1/4" Opening
Qty: 1
P/N: C-1042
Nut
8-32 - Kep
Qty: 4

  1. Remove payment device bay cover plate if still installed.

  2. Take C-0103-B LaundryCard Reader and remove the front bezel by unscrewing the four screws around the card slot.
  3. Attach the C-0103-B LaundryCard Reader to the C-0974 Flat Mount Bezel using the previously removed screws.
  4. Install C-0974 Flat Mount Bezel into the Payment Device Bay and secure using the C-1042 Kep Nuts.
  5. Apply the C-0014S Window Label over the display opening of the C-0974 Flat Mount Bezel.
  6. Apply the C-0015S Insert Card Label over the card slot opening of the C-0974 Flat Mount Bezel.

Surface Mount

P/N: C-0015
Label
Reader Cover Label
Qty: 1
P/N: C-0141
Screw
8-32 x 1-1/2" - Cap
Qty: 2
P/N: C-0930
Mounting Bracket
Unimac/ADC
Qty: 1

  1. Locate an appropriate location to cut a hole for the reader where the start harness can still reach the MDB connection on the control board, or with a MDB harness.

  2. Cut a hole into the machine's panel using the C-0930 Mounting Bracket as a template.
  3. Place C-0930 Mounting Bracket behind the panel and secure reader to the otherside using C-0141 screws.

Connect Machine Interface Harness

Serial

P/N: C-0124-MLV-40
Machine Start Harness
40"
Qty: 1

  1. Connect the C-0124-MLV-40 Machine Start Harness to the MDB harness connected to the the Machine Control Assembly.

Connect and Mount Reader

TODO - Include picture of LaundryCard reader connection

  1. Feed remaining harness ends through the mounting hole as described in the LaundryCard Kit Installation Guidelines.
  2. Connect the free end of the C-0124-MLV-40 Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.
  3. Secure the LaundryCard reader to the machine as described in the LaundryCard Kit Installation Guidelines.

Machine Configuration

TODO

LaundryCard Configuration

Use the following settings depending on the Machine Start Harness used.

Serial (C-0124-MLV-40)

  1. Equipment Type: Vending - MDB Level 1

    Page not found for multiexcerpt macro.
The page: null was not found. Please check/update the page name used in the 'multiexcerpt-include' macro.