LaundryCard Documentation
Space shortcuts
Page tree
Skip to end of metadata
Go to start of metadata

Overview

Equipment Details


Average Installation Time


On This Page

Make: ADC


TODO


Associated Models

EWH60M2
EWH30
EWH40
EWH40MC2
EWH40MR
EWH40MR
EWH40MR
EWH40MRC2
EWH60
EWH60M2
EWH60M2
EWH60M2
EWH60M2
EWH60M2
EWH60M2
EWH60M2
EWH60M2
EWH60M2
EWH60M2
EWH60M2
EWH60M2
EWR25
EWR40
EWR60
EWR60MR
EWS40M2
EWS40MC
EWS40MC
EWS40MC
EWS40MC2
EWS60M2
EWS60MC
EWS60MC
EWS60MC
EWS60MC
EWS60MC2
EWS60MR
EWS60MR
EWS80M2
EWS80MC1
EWS80MC2
EWS80MC2
EWS80MC2
EWS80MR
EWS80MR1

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

Part IDDescriptionImage
C-0103-B
LaundryCard Reader V3 - RevB

Recommended Tools and Supplies (Not Included)

Installation

    Page not found for multiexcerpt macro.
The page: null was not found. Please check/update the page name used in the 'multiexcerpt-include' macro.

Install Mounting Hardware

CCI Card Ready Models

P/N: C-0015
Label
Reader Cover Label
Qty: 1
P/N: C-1042
Nut
8-32 - Kep
Qty: 2
P/N: C-1043
Screw
8-32 x 1-3/4" - Flat
Qty: 2

  1. Install reader into card reader opening and secure with C-1042 Nut and C-1043 Screw.

Coin Ready Models

P/N: C-0015
Label
Reader Cover Label
Qty: 1
P/N: C-0035
Label
3-7/8" x 3-1/4"
Qty: 1
P/N: C-0133
Standoff
8-32" x 1-1/2" - Hex
Qty: 2
P/N: C-0140
Screw
8-32 x 3/4" - Cap
Qty: 2
P/N: C-0936
Vault Mount Bracket
Qty: 1

  1. Remove existing coin box and coin drop.

  2. Bend the side tabs of the C-0936 Bracket outward and install into the coin vault. The tabs should snap into place securing the bracket.

  3. Attach the C-0133 Standoffs to the Bracket.

  4. Secure reader to C-0936 Bracket using C-0140 Screw.
  5. Apply C-0035 Label over coin drop opening.

Connect Machine Interface Harness

Pulse

P/N: C-0111-RES
Machine Start Harness
Two Wire Harness w/ Resistor
Qty: 1

  1. Connect the C-0111-RES Machine Start Harness to the brown and yellow wires connected to the Machine Control Assembly.
    1. Wire pairing to the start harness is not relevant. 

Connect and Mount Reader

TODO - Include picture of LaundryCard reader connection

  1. Feed remaining harness ends through the mounting hole as described in the LaundryCard Kit Installation Guidelines.
  2. Connect the free end of the C-0111-RES Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Secure the LaundryCard reader to the machine as described in the LaundryCard Kit Installation Guidelines.

Machine Configuration

TODO

LaundryCard Configuration

Use the following settings depending on the Machine Start Harness used.

Pulse (C-0111-RES)

  1. Equipment Type: SingleVend
  2. Pulse Length: 100

    Page not found for multiexcerpt macro.
The page: null was not found. Please check/update the page name used in the 'multiexcerpt-include' macro.