Page tree
Skip to end of metadata
Go to start of metadata
Table of Contents
Overview and Equipment Information

This document is intended to guide the user through installation utilizing the kit numbered according to the document title. A list of associated equipment models including control information and additional installation notes can be found below.

Kit Installation Notes

Status: Active

Product: FasCard F1
Manufacturer: Alliance
Start Harness: 7-pin single row flat connector
Interface Type: Serial
Install Type: Card Only
Actuation: N/A
Coin Sense: N/A
Mounting: Surface Mount
Chassis: Small Chassis - Front Control
Readers: 1 Reader
Machine Control: Alliance MDC/Centurion

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

Part IDDescriptionImage
F1 FasCard Reader

Install Kit (K-5704-CO)

QTYPart NumberDescriptionImage
1C-0110-CPJumper Plug
1C-0110-TOPMachine Start Harness
3C-5101Spade Taps
1C-5210Power Adapter Harness
1C-5500Power Extension Harness
1C-5602Power Converter
1C-5800F1 Reader Mounting Kit

Recommended Tools and Supplies

See F1 Reader Mounting Guide for more information.


Confirm machine power is disconnected before beginning installation!

Use caution and appropriate protection to prevent hand and eye injury during installation!

Step 1 - Install Mounting Bracket

Drill Template
F1 Reader Mounting Kit

  1. Place the C-5700-TEMP Drill Template on the desired mounting location.
    1. Front Mount over card reader slot recommended.
    2. Alternative top mount can be used, recommend obtaining C-5633-R1 Label to cover card slot.
  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.
  3. Refer to F1 Reader Mounting Guide for further instructions.

Step 2 - Connect Power

Spade Taps
Power Adapter Harness
Power Extension Harness
Power Converter

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.
  2. Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.
  3. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Step 3 - Connect Machine Start Harness

Jumper Plug
Machine Start Harness

  1. Remove the existing Alliance Jumper Plug at H8 and connect the C-0110-CP Jumper Plug to the Machine Control Assembly.
  2. Connect the C-0110-TOP Machine Start Harness to the Machine Control Assembly at H5.
    1. The opposite end of this harness connects directly to the FasCard reader.

Step 4 - Connect and Mount FasCard Reader

Machine Start Harness
Power Extension Harness

  1. Feed harness ends through mounting hole as described in the FasCard Mounting Guide.
  2. Connect the C-0110-TOP Machine Start Harness to port 1 (Serial Communication Port) as shown above.
  3. Connect the C-5500 Power Extension Harness to port 4 (C-5500 Power Harness Connection Port) as shown above.
  4. Connect FasCard reader to base as described in the F1 Reader Mounting Guide.
  5. Program the card reader address as described here: How to Program Address on a FasCard Reader.

Associated Equipment Models

HuebschHD#BYA####1#W01Alliance MDC Small Dryer
HuebschHDET07WFAlliance MDC Small Dryer
HuebschHDEY07WFAlliance MDC Small Dryer
HuebschHF#BCF####2#N01Alliance MDC Front Load Washer
HuebschHF#BYF####2#W01Alliance MDC Front Load Washer
HuebschHFGY09#F1102Alliance MDC Small Dryer
HuebschHWFT####Alliance MDC Front Load Washer
IPSOBD#BYR####?#W01Alliance MDC Small Dryer
Speed QueenSD#BYA####1#W01Alliance MDC Small Dryer
Speed QueenSF#BYF####2#W01Alliance MDC Front Load Washer
Speed QueenSFGY09#FAlliance MDC Small Dryer
Speed QueenSWFY71#NAlliance MDC Front Load Washer