Page tree
Skip to end of metadata
Go to start of metadata

Overview

Equipment Details

Make: [VARIES]
Two separate controls. Dual pocket setup not supported at this time due to different equipment types.

On This Page

Associated Models

HTENXASP133DW01
HTENXASP133FW01
HTENXASP283CW01
HTENXASP293CW01
HTENXASP543DW01
HTENYASP283CW01
HTENYASP293CW01
HTGNXASP093CW01
HTGNXASP113FW01
HTGNXASP123DW01
HTGNXASP543DW01
STENCASP173TW01
STENCASP175TW01
STENCFSP176TW01
STENXASP133DW01
STENXASP133FW01
STENXASP173TW01
STENXASP175TW01
STENXASP283CW01
STENXASP293CW01
STENXASP433AW01
STENXASP543DN01
STENXASP543DW01
STENYASP173TN01
STENYASP173TW01
STENYASP175TW01
STENYASP176TW01
STENYASP283CW01
STENYASP293CW01
STENYFSP175TW01
STGNCASP113TW01
STGNCASP115TW01
STGNCASP116TW01
STGNCAST115TW01
STGNCFSP115TW01
STGNXASG113JW01
STGNXASG113TW01
STGNXASG115TW01
STGNXASP093CW01
STGNXASP113FW01
STGNXASP113TW01
STGNXASP123DW01
STGNXASP303AW01
STGNXASP543DN01
STGNXASP543DW01
STGNYASA115TW01
STGNYASP093CW01
STGNYASP113TN01
STGNYASP113TW01
STGNYASP115PW01
STGNYASP115TW01
STGNYAST115GW01
STGNYAST115TW01
STGNYFFT115TW01
STGNYFSP115TW01
STLNYASP543PW01

Recommended Tools and Supplies

Installation

Install Mounting Hardware

Kit: M12A-001 (Coin and Card)

Part #: C-6801

Desc 1: F2 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Kit: M12B-018 (Card Only - 10° Panel Coin Models)

Part #: C-1059

Desc 1: Nut

Desc 2: 10-32 - Kep

   Qty: 2

Part #: C-1070-W

Desc 1: Washer - Build: XCH

Desc 2: 1/4" x 1" O.D.

   Qty: 2

Part #: C-5365

Desc 1: Bypass Harness

Desc 2: Alliance Coin Vault Bypass

   Qty: 1

Part #: C-5414

Desc 1: F2 Standard Mounting Bracket

Desc 2: Sheet metal base

   Qty: 1

Part #: C-5416

Desc 1: Screw

Desc 2: 8-32" x 3/8" - Button - Torx

   Qty: 2

Part #: C-5420

Desc 1: Screw

Desc 2: 10-32 x ¼" - Pan

   Qty: 2

Part #: C-6765-W-R1

Desc 1: F2 Mounting Bracket

Desc 2: 10 Degree - White Finish

   Qty: 1

  1. Remove existing coin box and coin drop.

  2. Install the C-5365 Bypass Harness by removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness.
  3. Attach the C-5414 F2 Mounting Bracket to the C-6765-W-R1 Metercase Bracket using (2) C-5420 10-32 x 1/4 Pan Screws.
  4. Run any card reader harnesses through the coin slot openings and the circular hole in the C-6765-W-R1 Metercase Bracket.
  5. Install the C-6765-W-R1 Metercase Bracket so that the two threaded posts insert into the coin drop slots. Then secure it to the machine using the (2) C-1059 Kep Nuts and (2) C-1070-W Washers.

Kit: M12B-030 (Card Only - Flat Front Panel Coin Models)

Part #: C-0940

Desc 1: Vault Cover

Desc 2: 3-7/8" x 2-3/4"

   Qty: 1

Part #: C-5035

Desc 1: Label

Desc 2: 3-7/8" x 3-1/4"

   Qty: 1

Part #: C-5365

Desc 1: Bypass Harness

Desc 2: Alliance Coin Vault Bypass

   Qty: 1

Part #: C-6801

Desc 1: F2 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

  1. Remove existing coin box and coin drop.

  2. Install the C-5365 Bypass Harness by removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness.
  3. Bend the tabs outward and insert the C-0940 Vault Cover in to the coin vault opening.
  4. Apply the C-5035 Label over the opening for the coin drop.
  5. Place the C-6700-TEMP Drill Template on the desired mounting location.

  6. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  7. Refer to FasCard Mounting Guide for further instructions.

Kit: M12B-010 (Card Only - Card Models)

Part #: C-6801

Desc 1: F2 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Connect Power

Kit: P140-018 (ACA Controls)

Part #: C-6204-40

Desc 1: Power Adapter Harness

Desc 2: F2, 12vDC Pow Harness - 40"

   Qty: 1

  1. Connect the C-6204-40 12VDC Power Harness to the H10 connection on the Machine Control Assembly.
    1. Connect the green wire to a chassis ground.
  2. The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.

Kit: P120-005 (Titanium Controls)

Part #: C-6207

Desc 1: F2, Alliance ACA Power Hns

Desc 2:

   Qty: 1

  1. Connect the 2-pin connector from the C-6207 F2, ACA Power Harness to the 24v transformer behind the front control panel.
  2. The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.

Connect Coin Sense Harness

Kit: S12A-001 (Factory Optical Coin Drop)

Part #: C-6250

Desc 1: Coin Sense Harness

Desc 2: can use C-6250-144

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6250 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

Kit: T150-052 (Pulse - Coin)

Part #: C-5302

Desc 1: Machine Start Harness

Desc 2: MD2

   Qty: 1

  1. Connect the C-5300-NC Machine Start Harness to the coin 1 connector on the Machine Control Assembly.

Kit: T150-003 (Serial Communication / Serial Pulse)

Part #: C-5240

Desc 1: Machine Start Harness

Desc 2: can use C-5240-144

   Qty: 1

  1. Connect the C-5240 Machine Start Harness to the the H3 connection on the Machine Control Assembly or Communication board.

Connect and Mount Reader

  1. Feed remaining harness ends through the mounting hole.
  2. (Pulse - Coin Only) If using the C-5300-NC Machine Start Harness, connect the free end to port 2 (Pulse Connection Port) as shown in the image above.
  3. (Serial Comm Only) If using the C-5240 Machine Start Harness, connect the free end to port 5 (Serial Connection Port) as shown in the image above.
  4. (Coin and Card Installations Only) Connect the free end of the C-6250 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  5. Connect the free end of the C-6204-40 or C-6207 Power Harness to port 1 (Power Harness Connection Port) as shown in the image above.

Machine Configuration

ACA Controls

  1. Locate the dip switch on the back of the machine's control board.
  2. Set dip switch 3 to the ON position. 
  3. Leave all other dip switches as is.

Titanium Controls

  1. Enter Manual Mode by opening the service door and closing the coin vault switch. Then press the following two buttons based on the control:


    Quantum Gold Pro (T4)

    Galaxy 600 Pro (T2)

    MDC II (T1)

    DryerHigh Temp & Med TempHigh Temp & Med Temp

    High Temp & Med Temp

    WasherRegular & NormalHot & Blankets ColdNormal Hot & Perm Press Warm
  2. rAPid will be displayed on the control. Select the Prog option and then configure the following settings:
    1. Serial Payment Configuration (SErPAY): Card
    2. Card Enable (CArdEn): On
  3. Exit Manual Mode.

CCI Software Configuration

Machine Control: International (A3)
 Pulse: SingleVend (MLV+) / 80
 Serial: Alliance ACA H7S Front Load Washer A3 - International
Machine Control: International (A3)
 Pulse: SingleVend (MLV+) / 80
 Serial: Alliance ACA H7S Small Dryer A3 - International
Machine Control: Quantum+ (A4)
 Pulse: SingleVend (MLV+) / 80
 Serial: Alliance ACA H7S Front Load Washer A4 - Quantum+
Machine Control: Quantum+ (A4)
 Pulse: SingleVend (MLV+) / 80
 Serial: Alliance ACA H7S Small Dryer A4 - Quantum+
Machine Control: Titanium (T1)
 Pulse: SingleVend (MLV+) / 80
 Serial: Alliance Titanium Small Dryer T4
Machine Control: Titanium (T1)
 Pulse: SingleVend (MLV+) / 80
 Serial: Alliance Titanium Small Dryer T1
Machine Control: Titanium (T1)
 Pulse: SingleVend (MLV+) / 80
 Serial: Alliance Titanium Front Load Washer T4
Machine Control: Titanium (T1)
 Pulse: SingleVend (MLV+) / 80
 Serial: Alliance Titanium Front Load Washer T2

Additional Resources

  • No labels