Page tree
Skip to end of metadata
Go to start of metadata

Overview

Equipment Details


Average Installation Time


On This Page

Make: Dexter
Dryer Portion of Stack Washer/Dryer.


TODO


Associated Models

DCS030NC10EC1XSWBCGUSA
DCS030NC10EC1XSWBCGUSA
DCS030NC10EC1XSWBCGUSA
DCS030NC10EC1XSWBCGUSA
DCS030NC10EC1XSWGBGUSA

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

One of the following readers.

Part IDDescriptionImage
C-3001
LC WiFi Reader
Front/Vertical Mount
C-3002
LC WiFi Reader
Top/Horizontal Mount
C-5401
F2 FasCard Reader
Front Mount
C-5402
F2 FasCard Reader
High Front/Top Mount
C-5403
FLEX Reader
Front/Vertical Mount
C-5404
FLEX Reader
Top/Horizontal Mount

Recommended Tools and Supplies (Not Included)

See 2077 F2 Reader Install Guide for more information.

Installation

    Page not found for multiexcerpt macro.
The page: null was not found. Please check/update the page name used in the 'multiexcerpt-include' macro.

Install Mounting Hardware

Card Only

P/N: C-0144
Screw
8-32 x 2" - Flat
Qty: 2
P/N: C-5710
Rubber Grommet
3/4"
Qty: 1
P/N: C-6801
F2 Reader Mounting Kit
Universal
Qty: 1
P/N: C-6936
F2, Sm Vault Mount Bracket
Qty: 1

  1. Remove existing coin box.

  2. Insert the C-5710 Rubber Grommet into the central hole of the C-6936 Vault Bracket.
  3. Run all reader harnesses through coin vault and then the hole of the C-6936 Vault Bracket.
  4. Bend the side tabs of the C-6936 Vault Bracket outward and install into the coin vault. The tabs should snap into place securing the bracket.

  5. Run all reader harnesses through the central hole of the C-5414 Reader Bracket
  6. Attach the C-5414 Reader Bracket to the C-6936 Vault Bracket using the C-0144 screw.

Connect Power

P/N: C-5213
Power Adapter Harness
DDAD - AC
Qty: 1
P/N: C-5500-115
Power Extension Harness
115"
Qty: 1
P/N: C-5602R1
Power Converter
SMT-012-018VW
Qty: 1

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document by connecting the C-5213 Power Adapter Harness to the power distribution terminal block inside the machine.

    1. Connect the black wire to a L1 tab.

    2. Connect the white wire to a L2 tab.

    3. Connect the Green/Yellow wire to the ground tab.

  2. Connect the opposite end of the C-5213 Power Adapter Harness to the C-5602R1 Power Converter.

  3. Connect the C-5500-115 Power Extension Harness to the appropriate connector on the C-5602R1 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

Coin Drop: Factory

P/N: C-6258
Coin Sense Harness (SA)
WCAD
Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6258 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

Pulse

P/N: C-5254
Machine Start Harness
Dexter Stack Dryer
Qty: 1

  1. Connect the C-5257 Machine Start Harness to the P2 connector on the Machine Control Assembly.

Connect and Mount Reader

Item No.ComponentNotes
1Power Connection PortUtilizes the same power harnesses as the first generation FasCard reader.
2Pulse Connection PortConnection point for pulse machine start harnesses.
3Coin 1 Connection PortThis is the connection point for the harness input associated with Coin 1.
4Coin 2 Connection PortThis is the connection point for the harness input associated with Coin 2.
5Serial Connection PortThis is the connection point for serial machine start harnesses.

  1. Feed remaining harness ends through the mounting hole as described in the F2 Reader Mounting Guide.
  2. Connect the free end of the C-5254 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of the C-6258 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5500-114 Power Harness to port 1.
  5. Secure the FasCard reader to base as described in the F2 Reader Mounting Guide.

Machine Configuration

TODO

FasCard Admin Site Configuration

Use the following settings depending on the Machine Start Harness used.

Pulse (C-5254)

  1. Equipment Type: SingleVend
  2. Pulse Length: 55