Custom Install Scenario
This install guide has been created and intended only for use at FasCard account F0913, where a previous card system is being replaced.
C-5358 coin sense harness is being sent in place of the standard coin sense harness as the previous card system spliced into the coin drop harness.
Overview
Equipment Details | Average Installation Time | On This Page | ||
Make: Electrolux N = Normal Spin (100G) S = Super Spin (200G) TEST
0470 F1 Reader Install Guide
| TODO |
Known Models
W5105S
W5130N
W5130NCC
W5130S
W5130SCCBW:2
W5180N
W5180NCC
W5180S
W5180SCCBW:2
W5250N
W5250S
W5250SCC
W5250SCCBW:2
W5300S
W5330N
W5330S
W5330SCCBW:2
W5350S
W5380S
This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.
Required Hardware
Card Reader
| Part ID | Description | Image |
|---|---|---|
| C-5001 | F1 FasCard Reader |
Recommended Tools and Supplies (Not Included)
See 0470 FasCard F1 Install Guide - Custom Install 01 for more information.
Installation
- Page not found for multiexcerpt macro.
Install Mounting Hardware
Coin and Card
Place the C-5700-TEMP Drill Template on the desired mounting location.
Verify included harnesses will reach desired location without encountering interference from internal machine components.
Refer to FasCard Mounting Guide for further instructions.
Connect Power
- Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.
- Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.
- Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.
Connect Coin Sense Harness
Coin Drop: Factory
- Disconnect the Coin Drop from the previous card reader.
- Connect the C-5358 Coin Sense Harness to the harness connected to the Coin Drop.
- Connect the White wire from the coin drop to the White wire terminal on C-5358.
- Connect the Green wire from the coin drop to the Green wire terminal on C-5358.
- Connect the Brown wire from the coin drop to the Brown wire terminal on C-5358.
Connect Machine Interface Harness
Serial
- Connect the C-0126-MLV Machine Start Harness to the RS-232 port on the Machine Control Assembly.
- Connect the C-5359 Machine Start Harness to the Input 1 port on the Machine Control Assembly.
Connect and Mount Reader
- Page not found for multiexcerpt macro.
- Feed remaining harness ends through the mounting hole as described in the F1: FasCard Reader Mounting Guide.
- Connect the free end of the C-0126-MLV Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.
- Connect the free end of the C-5359 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
- Connect the free end of the C-5358 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
- Connect the free end of the C-5500 Power Extension Harness to port 4 (Power Harness Connection Port) as shown in the image above.
- Secure the FasCard reader to base as described in the FasCard Mounting Guide.
Machine Configuration
TODOFasCard Admin Site Configuration
Use the following settings depending on the Machine Start Harness used.
Serial (C-0126-MLV)
- Equipment Type: Laundrylux Compass Pro Washer
- Page not found for multiexcerpt macro.