Page tree
Skip to end of metadata
Go to start of metadata

Overview

Equipment Details

Make: Milnor

On This Page

Associated Models

MCR12E5
MCR16E5
MCR18E4
MCR18E5
MCR27E4
MCR27E5
MCR36E4

Recommended Tools and Supplies

Installation

Install Mounting Hardware

Kit: M02A-003 (Coin and Card)

Part #: C-5801

Desc 1: F1 Reader Mounting Kit

Desc 2: Front

   Qty: 1

  1. Place the C-5700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Connect Power

Kit: P060-010 (Tap Machine Power)

Part #: C-5101

Desc 1: Spade Taps

Desc 2: 18-14 AWG

   Qty: 3

Part #: C-5210

Desc 1: Power Adapter Harness

Desc 2: CGI

   Qty: 1

Part #: C-5500-60

Desc 1: Power Extension Harness

Desc 2: 60"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

  1. Use the C-5101 Spade Taps on the incoming power.
    1. Tap the L1 wire.
    2. Tap the L2/N wire.
    3. Tap the Ground wire.
  2. Take the C-5210 Power Adapter Harness and connect the red tab connectors to the following wires:
    1. Connect the blue wire to the L1 wire.
    2. Connect the brown wire to the L2/N wire.
    3. Connect the green/yellow wire to the Ground wire.
  3. Connect the 3-pin connector from the C-5210 Power Adapter Harness to the matching connection on the C-5602R1 Power Converter.
  4. Connect the 4-pin connector from the C-5602R1 Power Converter to the matching connection on the C-5500-60 Power Extension Harness.

Connect Coin Sense Harness

Kit: C020-002 (Factory Coin)

Part #: C-5310

Desc 1: Combination Harness

Desc 2: Gen Pulse Sense Eye

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.
    1. If the Coin Drop sensor harness does not have a disconnect, it must be cut and stripped.
  2. Connect the C-5310 Combination Harness to the disconnected wires leading to the Coin Drop. Connect each of the wires to the corresponding color on the terminal block with the red, green, and blue wires.

Connect Machine Interface Harness

Kit: C020-002 (Pulse - Coin Drop)

Part #: C-5310

Desc 1: Combination Harness

Desc 2: Gen Pulse Sense Eye

   Qty: 1

  1. Connect the end with the Green and Blue with jumper wire end to the machine.
    1. Red wire connects at the Jumper. Green and blue wires connect to the corresponding connections.
  2. Disconnect wires from Coin Block solenoid.
    1. Connect these wires to the White (male) spade connector on the C-5310 Combination Harness.
  3. Connect White (female) spade connector on C-5310 Combination Harness to the Coin Block solenoid.

Connect and Mount Reader

  1. Feed remaining harness ends through the mounting hole.
  2. Connect the white, 6-pin connector of the C-5310 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the black, 5-pin connector of the C-5310 Coin Sense Harness  to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5500-60 Power Extension Harness to port 4 (Power Harness Connection Port) as shown in the image above.

CCI Software Configuration

Machine Control: *NO NAME*
 Pulse: SingleVend (Relay) / 75
 Serial:

Additional Resources

  • No labels